Articles

95
Be Prepared - Preparatory Site Visits Reduce Project Cost and Risk When Planning the Intelligent Pigging of Oil Terminal Wharf Pipelines
By: Geert Bontekoe and Laurie Todd, Quest Integrity

As seen in the Winter 2017 issue of Tanks & Terminals Magazine

90
Pipeline Pigging Q&A
World Pipelines asked a number of companies to discuss issues regarding pigging for oil and gas midstream pipelines. Quest Integrity's Dan Revelle offers insight on the industry.

100
Risky Business - Mitigating High Temperature Hydrogen Attack
By: Chris Jones, Charles Thomas, and David Keen

As seen in the September / October issue of World Fertilizer Magazine

89
Custom ILI Tool Inspects Unpiggable Multi-Diameter Pipeline
Special report by Quest Integrity, featured in World Pipelines.

91
Baseline Inspection Provides Head Start on Heater Reliability and Longevity
Special report by Quest Integrity, featured in Hydrocarbon Engineering.

96
Method for Assessing a Deformed Spillway Gate
By: Vitor Lopes Garcia and David Osuna, Quest Integrity

As seen in the July 2017 issue of Hydro Review Magazine

97
Advanced Buckling Analysis of a Reactor Tank Supported by Four Legs
By: Michael Turnquist, Quest Integrity

As seen in the July/August 2017 issue of Inspectioneering Journal

94
Optimizing Critical Fired Heaters, Now Easier than Ever
Special report by Quest Integrity, featured in the May 2017 issue of Chemical Engineering.

98
Quest Integrity Pipeline Q&A
As seen in the April 2017 issue of World Pipelines Magazine.

87
A Closer Inspection - How Highly Developed Inspection Tools are Used to Identify Tubular Damage
By: Charles Thomas and Dan Drabble, Quest Integrity

As seen in the March/April 2017 issue of World Fertilizer Magazine.

99
Predicting the Future of ILI Tools
By: Robert De Lorenzo, Quest Integrity

As seen in the February 2017 issue of World Pipelines Magazine.

93
My Pipes are Corroding! When Should I Repair?
By: Michael Turnquist, M.Sc., Quest Integrity

As seen in the November/December 2016 issue of Inspectioneering Journal.

85
ILI and Hydrostatic Testing - Mastering Multitasking
By: Rusty Jackson, Manager, Quality & Training at Quest Integrity

As seen in the October 2016 issue of World Pipelines Magazine.

Hydrostatic testing is often the preferred method of inspection for ageing pipelines, sometimes due to limited data. This has raised questions about the ability of inspection tools to successfully navigate the pipeline. In the case studies presented in this article, an ultrasonic inline inspection (ILI) was performed in conjunction with the hydrotest.

86
Choosing the Right Smart Pigging Technology - Lessons Learned
By: Tim Haugen, Process Inspection Service Line Director, Quest Integrity

84
Empirical Guidelines for Fitness-For-Service Assessment of Wicket Gates
By: Eric Scheibler, Senior Consulting Engineer and Global Hydropower Manager, Quest Integrity
Matt Clemmer, Hydro Generation Engineering Manager, Tennessee Valley Authority

As seen in Hydro Review, Volume 35, Issue 7.

A cascading wicket gate failure at one of its 1940s-era plants prompted the Tennessee Valley Authority to develop fitness-for-service evaluation criteria, using as a basis technical studies at its 124-MW Hiwassee facility.

83
Fired Heater Health Monitoring and Reliability Management in Challenging Times
By: Tim Hill, Principal Consulting Engineer at Quest Integrity

As seen in the March/April issue of Inspectioneering Journal.

The reliable operation of fired heaters is critical to the successful performance of any petroleum refinery. Because they operate under such extreme conditions, the life of furnace tubes is often limited by creep, corrosion, and oxidation. This article covers many essential elements for optimizing the performance and reliability of fired heaters.

82
Reformer Performance and Tube Life Management
As seen in the January/February 2016 issue of Nitrogen + Syngas Magazine

The steam reformer is widely accepted as being the most complex and energy intensive part of any ammonia, methanol or hydrogen plant, and as such, it is important to ensure that it is operating and maintained under the best possible conditions. This will enable the operators to produce the maximum achievable levels of product, extend reformer tube lives and increase energy efficiency.

81
Inspecting Fired Heaters with Plug Headers: Obtaining Complete Data to Maximize Life
By: Quest Integrity

As featured in Hydrocarbon Processing.

Recent advances in ultrasonic-based intelligent pig technology allows for the inspection of fired heater coils that include plug headers, without requiring costly coil modifications such as radial or deflector inserts.

64
How to Assess Pipeline Anomalies and Effectively Prioritise Pipeline-Integrity Digs
By: Ian Smith, Senior Consulting Engineer, Quest Integrity

As seen in the December 2014 issue of Pipelines International

Quest Integrity Group was recently contracted by the pipeline-integrity department of an offshore offloading facility to perform an ultrasonic in-line inspection of a 4 inch pipeline. By employing advanced engineering technology, the company was able to reduce the integrity department’s pipeline-integrity digs from 16 to three, saving time and money.

63
Effective Integrity Management Programs for Steam Reformers
By: Kelsey Hevner,Technical Advisor - Syngas at Quest Integrity Group

As seen in the Nov-Dec 2014 issue of Inspectioneering Journal

An effective integrity management program for steam reformers that focuses on tube integrity encompasses these essential parts: inspection, data analysis, and remaining life assessment.

Default template/mod not set, contact Site builder
Default template/content not set, contact Site builder, $custompagetemplateid: 1 PathToCurrentPage: / $FileName: articles.php
LEARN MORE
Default menu not set, contact Site builder
Default template/content not set, contact Site builder, $custompagetemplateid: 1 PathToCurrentPage: / $FileName: articles.php